menu

CCS Natural Supreme HV is a solvent based silane-siloxane penetrating sealer designed to protect both horizontal and vertical surfaces from the ingress of water and salts.

Once it penetrates the surface, CCS Natural Supreme HV will produce a hydrophobic bond.

Due to its penetrating capabilities CCS Natural Supreme HV does not change or alter the colour of the surface ensuring the original natural look of the substrate is retained.

Recommended Uses
  • To protect and treat masonry, concrete, pavers, natural stone and tile from the ingress of water and water borne chemicals.
  • Protection for reinforced concrete from salts and chlorides.
  • For use on clean plain or coloured concrete, cement based renders, concrete pavers, clay bricks, sandstone, marble, limestone and travertine.
  • Ideal for pre-cast panels, tilt-up panels and wall cladding.
Curing

Allow the sealer to cure for at least 4–6 hours before subjecting to pedestrian traffic and 7 days for vehicular traffic, trolleys, wheel mounted bins or any other equipment that could impact or mark the surface. Please note that whilst the sealer is in the curing phase a slight residue may initially be felt underfoot.

Coverage

Coverage is approximately 5m2 per litre depending on surface porosity. A minimum of two coats applied to saturation, is recommended for effective treatment. A third coat may be required for very porous surfaces.

Surface Preparation

Concrete, Natural Stone and Porous Tile

All surfaces to be treated must be structurally sound and all previous coatings, curing compounds, adhesives, efflorescence or laitance should be removed by abrasive blast cleaning, high pressure water washing or mechanical scrubbing.

Application Guidelines

Concrete, Natural Stone and Porous Tile

CCS Natural Supreme HV should be applied undiluted using a low pressure sprayer, brush, broom, or lambs wool applicator.

If using a low pressure sprayer, ensure that you also work the product into the surface using a lambs wool applicator.

Note: Concrete must be cured for a minimum of 28 days before applying CCS Natural Supreme HV.

  1. Apply the first coat to saturation point and allow sufficient time for penetration, making sure to fill all voids and surface irregularities.
    NOTE: If using a low pressure sprayer, ensure that the product is worked into the surface using a lambs wool or microfibre applicator. Should ponding or pooling occur, immediately wipe off excess product or work the product into the surface.
  2. When the surface becomes touch dry, after approximately one hour, apply a second coat as described in step one (above) again ensuring that no ponding or pooling occurs as this may lead to a patchy appearance and other related issues.
Clean Up

Clean tools and equipment using CCS Solvent.

Precautions
  • CCS Natural Supreme HV is not designed as a waterproofing compound.
  • Do not thin or dilute the sealer.
  • Do not apply on damp or wet surfaces.
  • Ensure the sealed surface is protected from moisture for a minimum of six hours after application.
Storage

Store in a bunded area or in an approved flammable store away from direct heat.

Features and Benefits
  • Provides surface protection against water and salts
  • Ideal for horizontal and vertical surfaces
  • Natural look
Packaging

CCS Natural Supreme HV is available in 20 litre drums.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…