menu

CCS Decrathane Satin is a clear, water based high performance, two component polyurethane coating system formulated to protect concrete from solvents, chemicals, oils and acids.

It is ideal as a replacement for traditional epoxy based coatings where a satin finish and less downtime is required.

Recommended uses
  • High traffic areas
  • Honed or polished concrete
  • Domestic and retail flooring
  • A UV stable top coat for CCS Ultra Epoxy floor coatings
  • Over Epoxies
  • Garage and workshop floors
  • Anywhere a satin, low VOC coating is required
Performance Properties
ColourClear
OdourSlight
Pot LifeUp to 3 hours
Mixing Ratio4 : 1 (Part A : Part B)
FinishingSatin
Volume SolidsApprox. 44% (Mixed)
Specific GravityApprox. 1.07 @ 25ºC
Drying Time**30–90min @ 25ºC 65% RH
Re-coat Time3–6 hours @ 25ºC 65% RH
Second coat must be applied within 24 hours
Full Cure**5–7 days @ 25ºC 65% RH
Spread Rate7–10m2 / litre approx.
** Dependent upon climatic conditions; relative humidity, Air/object temperature and air movement.
Coverage Rates
ColourClear
First coat7–9m2 / litre
Second coat8–10m2 / litre
Note: A minimum of two coats should be applied.
Surface Preparation

All surfaces to be treated should be structurally sound. All previous coatings, adhesives and efflorescence or laitance should be removed by mechanical grinding or abrasive blast cleaning, high pressure water blasting, mechanical scrubbing or other suitable means.

Holes, non-structural cracks and other surface deformities should be repaired using the CCS Epoxy Repair Kit in accordance with the technical data sheet. New concrete floors should be at least 28 days old before applying CCS Decrathane Satin.

Application Guidelines

CCS Decrathane Satin should be applied with a lambswool, mohair or 10–12mm nap roller, brush or airless sprayer.

A cross-hatching method of application should be used to avoid lap marks.

Application of First Coat

WARNING – If not mixing a complete kit it is critical that the correct volumes of Part A and Part B are used (4:1).

  1. Using a mechanical mixer, premix each individual component (i.e. Part A and Part B) until homogeneous. Ensure the mixer is thoroughly cleaned between each component to eliminate cross contamination and cured product being mixed with new batches.
  2. Add Part B (Hardener) to Part A (Base) and mechanically mix for 1–2 minutes. Scrape down the sides of the  container and mechanically mix for a further 1–2 minutes.
  3. Add 20% water to the mixed product, i.e. 200ml of water to every 1 litre of mixed together Part A & Part B. This will assist to maintain a wet edge.
  4. Mechanically mix for a further 1–2 minutes.
  5. Leave material to stand for 5 minutes prior to application. Only mix as much material as you are going to use within the pot life of the product (approximately 3 hours depending on climatic conditions).
  6. Apply the first coat of CCS Decrathane Satin at a rate of 7–9m2 per litre. If applying with a roller use a cross-hatching method of application to avoid lap marks.
  7. Ensure the first coat is dry before application of a second coat. Curing time for the first coat is usually between 3-6 hours depending on climatic conditions and whether the project is located indoors or outdoors.

WARNING – The second coat must be applied within 24 hours of the first coat to ensure that the second coat will key into the first coat. If the second coat is not applied within 24 hours the first coat will require light sanding or softening prior to application of a second coat. Contact your CCS representative for advice.

Application of Second Coat
  1. Ensure that a clean bucket and mixer is used before commencing mixing and application of the second coat.
  2. Mix the second coat in the same manner as the first together with 10–20% water.
  3. Apply the second coat of CCS Decrathane Satin by roller at a rate of 8–10m2 per litre. If applying with a roller use a cross-hatching method of application to avoid lap marks.

WARNING – The second coat must be applied within 24 hours of the first coat to ensure that the second coat will key into the first coat. If the second coat is not applied within 24 hours the first coat will require light sanding or softening prior to application of a second coat. Contact your CCS representative for advice.

Appropriate Surface Texture

As a general statement, the application of a coating to concrete will reduce the existing slip resistance of that surface. Consequently, care must be taken before sealing concrete to ensure that the surface texture has sufficient profile to provide adequate traction. However, as the sealer wears, the traction additives will also diminish in effectiveness.

CCS Glass Beads can also be added to aid traction. CCS Glass Beads should be applied during the application of the first coat by casting it onto the surface in a uniform manner.

A second coat of CCS Decrathane Satin should then be applied over the glass beads within 24 hours.

Curing

Allow the sealer to cure for at least 24 hours before subjecting to pedestrian traffic and 7 days for vehicular traffic or any other equipment that could impact, mark or damage the surface.

Precautions

CCS Decrathane Satin should not be applied to surfaces subject to hydro static pressure or rising dampness. Prior to using CCS Decrathane Satin the manufacturer should be consulted if the following conditions exist:

  • The concrete substrate is porous or in poor condition
  • The surface is subjected to unusually cold conditions (i.e. below 10ºC)
  • The surface is subjected to unusually high temperature above ambient temperatures whilst in service (e.g. floors subjected to hot or boiling water)
  • The floor is subjected to severe chemical attack.

Other Precautions

  • The pot life is approximately 3 hours. Discard any leftover mixed material after this time.
  • Do not apply when relative humidity exceeds 85%.
  • Do not apply when temperature exceeds 32 degrees or onto a hot substrate
  • Do not re-seal mixed product as pressure build up may occur.
Clean Up

Wash all equipment in water or a water/detergent mix immediately on completion of application and mixing.

Storage

Store between 10ºC and 30ºC away from direct sunlight. Partly used containers must be sealed tightly when not in use.

Features and Benefits
  • Can be used internally and externally
  • Easy to clean surface
  • Low odour, low VOC
  • Water based product
  • Excellent adhesion to most substrates including prepared concrete
  • Produces an attractive satin finish
  • Excellent chemical and stain resistance
  • Excellent scratch resistance
  • Excellent wear resistance
  • Can be made anti-slip (with addition of anti-slip particles)
Packaging

CCS Decrathane Satin is available in a 20 litre kit:

  • Part A (Base): 16 litres
  • Part B (Hardener): 4 litres

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…