menu

ACS Floor Maestro Self Levelling Compound is a
commercial grade cementitious self-levelling compound
with outstanding flow, workability and bonding properties.
ACS Floor Maestro Self Levelling Compound is suitable
where a thickness of feather edge to 50mm is required and
can be used over new or existing interior and exterior floors
that have been properly prepared and primed with CCS
Super Polymer.

Preparation

Concrete floors must be structurally sound, clean and dry.
Surface must be free from all contaminants such as dust,
dirt, wax, grease, asphalt, latex and gypsum compounds,
adhesives, paint, curing and sealing compounds all of which
may act as a bond breaker. Concrete must be free from
laitance, efflorescence and not be subject to hydrostatic
pressure. Mechanically prepare the floor using recommended
preparation methods such as shot blasting, scarifying, diamond
grinding, or other suitable methods to provide a roughened,
clean, sound, solid and open porous surface. Acid etching is
not a suitable method of preparing the subfloor. Remove all
dust and debris from the floor by vacuuming the surface with a
suitable H Class industrial cleaner which must be equipped with
a Hepa filter. All concrete sub floors must be fully cured and dry
in accordance with AS 1884 (Less than 75% relative humidity
when measured in accordance with ASTM F2170). Ambient
temperature, surfaces and materials should be maintained
at temperatures higher than 10°C and below 35°C. For floors
with a high humidity content or subject to rising damp, apply a
suitable moisture barrier compound. Refer to ACS Technical
Bulletin on Concrete Subfloor Preparation for detailed
information on preparation of the subfloor.

Application

Pour the mixed ACS Floor Maestro Self Levelling
Compound onto the prepared substrate and spread into
place using a long handled gauged spreader. ACS Floor
Maestro Self Levelling Compound seeks its own level
during the first 10 – 15 minutes after pouring. Subsequent
applications of leveller should be made whilst the material
on the floor is still fluid and has a wet edge, to allow for easy
blending. The ACS Floor Maestro Self Levelling Compound
can be applied from feather edge to 50mm thick in one
application. Thicker applications may require a longer cure.
It is recommended that spiked shoes be worn, to minimise
any indentations in the product whilst still fluid.

Setting Time

Allow a cure time of 3-4 hours at 23°C for foot traffic. Allow
the ACS Floor Maestro Self Levelling Compound to cure 24 hours at 23°C before laying floor coverings or coatings.
These times can be impacted by air temperature, substrate temperature and relative humidity. Thicker layers will extend drying times.

Features and Benefits
  • May be applied to a thickness of feather edge to 50mm in a
    single application
  • Tear and rain resistant recyclable PE bags which prevent
    loss from broken bags
  • Iron free formulation – will not rust or stain
  • Accurate and reliable bag weights
  • Excellent bonding properties
  • Outstanding flow and workability
  • Trafficable after 4 hours
  • Suitable for both manual and pump installation methods
  • Excellent non-sag properties when mixed to a stiff or
    plastic consistency
Packaging

ACS Floor Maestro Self Levelling Compound comes in a 20kg bag.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…