menu

CCS Same Day Sealer is a ready to use specially modified resin and solvent based acrylic sealer, designed for same day application to freshly poured concrete.

Note: CCS Same Day Sealer is not a diluted version of CCS Hardseal. CCS Same Day Sealer is formulated using a soft acrylic resin purposely made for application to wet concrete surfaces. In addition to this special resin, slow drying solvents are utilised to provide greater tolerance to moisture in the slab.

A relatively high resin content is also used in Same Day Sealer to assist in providing enhanced curing properties. The high resin content acts as a skin to help slow the moisture loss from the slab, and in so doing, enhance the strength of the concrete.

Due to the softness of the resin, Same Day Sealer does not provide adequate long term abrasion resistance. We recommend that two coats of either CCS Hardseal Advanced or CCS Hi-Build Enduro should be applied 7 days after the application of Same Day Sealer.

Recommended uses
  • Plain Concrete
  • Full Depth Coloured Concrete
  • Exposed Concrete and Stencilled Concrete

These surfaces should then be sealed after a minimum of 7 days with 2 coats of CCS Hardseal Advanced or CCS Hi-Build Enduro Sealer.

Note: Allow freshly laid concrete to dry for at least 7 days prior to application of the CCS finishing acrylic sealer such as CCS Hardseal Advanced, Hardseal Matt and Hi-Build Enduro.

Coverage

For application where one coat is applied, coverage is approximately 5m2 per litre depending on the porosity of the surface.

Application Method

Apply CCS Same Day Sealer to freshly laid concrete once concrete has cured enough to be walked on.

Note: CCS Same Day Sealer should be applied on the same day as the concrete was placed. This product is best applied using a solvent resistant low-pressure sprayer.

Curing

Curing time depends on the temperature. The sealer is usually touch dry in 20 minutes at 25ºC.

Note: Do not apply the finishing acrylic sealer if concrete is patchy in appearance. Often these are signs that the concrete may require further curing time.

Clean up

Wash all equipment thoroughly in CCS Solvent and allow to dry.

Features and Benefits
  • Formulated for wet on wet application to fresh concrete
  • Provides immediate protection against dirt and job site contaminants
  • Enhances curing
  • Can overcoat with CCS Hi-Build Enduro
Packaging

Same Day Sealer is available in 20 litre and 200 litre drums.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…