menu

CCS Petrol Resistant Sealer is formulated with a tough resin that does not soften when exposed to intermittent petrol spillage. In contrast, conventional acrylic sealers will soften and emulsify when petrol is spilt on them, causing the surface to become tacky and slippery.

Designed as a minimum two coat system, Petrol Resistant Sealer provides excellent protection against the fading or leeching of oxides in concrete, and staining or marking due to contaminants including grease, oil and dirt.

CCS Petrol Resistant Sealer has been specially formulated for service stations, workshops and factory floors where petrol and chemical spills can be hazardous with conventional concrete sealers.

Recommended Uses
  • Plain, coloured and stencilled concrete
  • Stamped/patterned concrete
  • CCS Stylepave or ‘sprayed-on’ concrete
Colours
  • Clear
  • Shale Grey
  • Black
Coverage

Coverage is approximately 4–5m2 per litre per coat. Where two coats are applied, coverage is approximately 40–50m2 per 20 litre drum. Refer to the chart below for first coat dilution rates. Always dilute with CCS Solvent.

Coverage based on finish
Concrete FinishSolvent : Sealer
Stencil1 litre : 4 litres
Smooth or pattern1 litre : 4 litres
Spray-on resurfacingIf required
Application Method

Best results are achieved by using a CCS Solvent Resistant Broom Head. A low pressure sprayer or roller can also be used, however penetration into the concrete is not as effective.

Allow freshly laid concrete that has been treated with CCS Same Day Sealer to cure for at least 7 days prior to application of sealer.

Fresh concrete that has not been treated with CCS Same Day Sealer or a curing agent should be left to cure for a minimum of 28 days prior to application. Do not apply to concrete that has a patchy appearance.

Preparation

Existing Concrete

To ensure all surface contaminants are removed, apply CCS HD Degreaser or CCS Citric Cleaner to the surface, ensuring the removal all oil stains.

Scrub the surface with auto scrubbing equipment or use a high pressure water cleaner to remove contaminants, ensuring all traces of the degreaser are thoroughly removed.

New Concrete

Fresh concrete that has not been treated with CCS Same Day Sealer or a curing agent should be left to cure for a minimum of 28 days prior to application.

Remove all oil, grease and dirt using CCS HD Degreaser. Then thoroughly wash the surface using auto scrubbing equipment or a commercial high pressure water cleaner. Ensure the concrete surface is clean and dry. Application of the sealer to moist concrete may cause the sealer to turn a white colour.

Where efflorescence or laitance is present, a mild citric cleaner wash may be required. Use CCS Citric Cleaner as per the label and data sheet instructions.

All concrete surfaces must be thoroughly dry before applying any sealer.

Resealing Concrete

Concrete surfaces that have previously been sealed with a solvent based acrylic sealer must be prepared by removing all loose and/or delaminated material.

Solvent scrub with CCS Solvent prior to immediate application of diluted CCS Petrol Resistant Sealer.

If the existing sealer is flaking / peeling, it is necessary to completely remove the coating with CCS Enviro Stripper. Ensure the surface is thoroughly rinsed and dry before applying any sealer.

First Coat
  1. The first coat should be diluted as per table above. A minimum of 2 coats should be applied to concrete.
  2. To apply, use a CCS Solvent Resistant Broom Head, short napped roller or a solvent resistant low-pressure sprayer.
    Spread the sealer over the entire surface in an even and systematic way so that the concrete is completely covered. If ‘pooling’ occurs, immediately spread the accumulated sealer.
  3. Allow a minimum of six hours between coats. For best results, allow 24 hours before applying the final coat.
Second Coat
  1. Stir thoroughly and apply as per first coat method above,
    however thinning is not required.
  2. Apply the second coat in the opposite direction to the first coat.
  3. A traction aid such as CCS Sealer Grit can be added on the final coat.
Clean up

Wash all equipment thoroughly in CCS Solvent and allow to dry.

Curing

Curing time depends on the temperature. The sealer is usually touch-dry in 20 minutes at 25ºC. The concrete can usually be walked on after 24 hours. Allow 7 days before allowing vehicular traffic.

NOTE: CCS Petrol Resistant Sealer should not be used as a curing compound.

Appropriate Surface Texture

Generally, applying a coating to concrete will reduce the existing slip resistance of that surface.

Consequently, care must be taken before sealing concrete to ensure that the surface texture has sufficient profile to provide adequate traction.

To aid traction, mix a satchel of CCS Sealer Grip additive into the sealer prior to application of the final coat. However, as the sealer wears, the traction additives will also diminish in effectiveness.

Coating Maintenance and lifespan

The expected lifespan of the coating is dependent on the location, weather and traffic the concrete is subjected to.

One major benefit of all CCS solvent based sealers is the ease of re-coating.

Assess the surface after 12 months, 18 months and 24 months from the date of application to determine if it requires recoating. In light use areas that are protected from adverse weather conditions, the coating will last much longer.

Features and Benefits
  • Does not soften when exposed to petrol and chemical spills
  • Specially formulated for service stations, workshops and factory floors
  • Available in three colours: Clear, Shale Grey & Black
Packaging

CCS Petrol Resistant Sealer is available in 20 litre drum.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…