menu

ACS Pitcrete WR 60 is a pre-packaged gypsum based sprayable grout ventilation control system, which, when compared to standard gypsum based products in the market, displays superior resistance to water absorption. The product is predominantly designed for use within, but not restricted to, mining applications.

A single application product, ACS Pitcrete WR 60 provides superior strength characteristics, premium water resistance qualities and a reduction in application time and costs.

It is particularly suitable for underground ventilation control devices and sealing applications. Because of its premium water resistance qualities, a waterproofing membrane is usually not required prior to application.

Recommended Uses

ACS Pitcrete WR 60 is typically used in underground mining applications for ventilation sealing, where there is a higher presence of water therefore requiring a product with higher than normal water resistance to moisture absorption.

Technical Properties

Typical properties when mixed with the appropriate amount of potable water and tested at 25ºC and 50% RH.

Application

The surface to be sprayed should be prepared by removing all unsound materials and debris.

ACS Pitcrete WR 60 can be applied in depths of 10 – 200mm in one pass depending on the spraying method used, as well as substrate and weather conditions.

ACS Pitcrete WR 60 may be applied over an extended time of two different shifts by cold bonding to the previous layer.

Cleaning

All tools should be rinsed with water immediately after use to remove all traces of ACS Pitcrete WR 60.

Storage

The product will keep indefinitely if kept dry and stored in its original condition.

The shelf life of the product may be reduced if subjected to moisture, high temperatures and high humidity.

Health and Safety

During use, avoid inhalation of dust and contact with the skin and eyes. Wear suitable clothing, gloves, eye protection and respiratory protective equipment.

If contact with the skin occurs, thoroughly clean the area with plenty of fresh water and soap. In case of contact with the eyes rinse with plenty of fresh water and seek medical advice.

If swallowed, seek medical attention immediately – do not induce vomiting.

For further information consult the Safety Data Sheet (SDS) and read the product label carefully before use.

Features and Benefits
  • Convenient and accurate – supplied ready to use under stringent quality control standards
  • Single, easy application in dry-mix spray systems – saves time and labour costs
  • Requires no waterproofing membrane due to high water resistance
  • Cures to an off-white colour and therefore requires no over-coating
  • Greater than 35% less dust characteristics for safer and easier application
  • Minimal rebound in dry sprayed processes
  • High early strengths for early re-entry to work area
Packaging

ACS Pitcrete WR 60 is available in 20kg bags or 1.1 tonne bulk bags.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…