menu

ACS Quick Drive is a high strength, pre-mixed product containing accurately weighed Portland cement, specially graded coarse and fine aggregates, and quality admixtures. 

It has been specifically designed to provide high early strength for the rapid repair and construction of underground drives and haul roads.

Recommended Uses

Because of its rapid setting qualities and overall performance strength, ACS Quick Drive is used for the repair and construction of underground roads and tunnels in civil and mining projects.

Coverage

ACS Quick Drive will yield 2300kg per m3.

Application
  1. Prepare the area to be concreted by removing any loose material.
  2. Thoroughly wet the area where the ACS Quick Drive is to be placed.
  3. Add the required amount of ACS Quick Drive to the area to be repaired or surfaced.  Note:To assist with even product hydration and to minimise dusting, lightly hose the dry product as it is being placed.
  4. Place the material to the required profile and then thoroughly wet the top surface. We recommend a depth of 100 – 150mm per layer. Note: We recommend wetting the surface between each layer of ACS Quick Drive.
  5. Should the surface require screeding it is imperative that this occurs WITHIN 10 MINUTES or as soon as the material has been profiled and wet.
Clean Up

Clean all equipment, surrounding areas and surfaces immediately with water.

Storage

ACS Quick Drive will keep for up to 12 months if kept in a dry store, off the ground and providing the bags remain sealed.

Health and Safety

During use, avoid inhalation of dust and contact with the skin and eyes. Wear suitable clothing, gloves, eye protection and respiratory protective equipment.

If contact with the skin occurs, thoroughly clean the area with plenty of fresh water and soap. In case of contact with the eyes rinse with plenty of fresh water and seek medical advice.

If swallowed, seek medical attention immediately – do not induce vomiting.

For further information consult the Safety Data Sheet (SDS) and read the product label carefully before use.

Features and Benefits
  • High early curing characteristic enables the surface to be trafficable within hours
  • Supplied pre-mixed and manufactured to strict quality assurance guidelines
  • Convenient – requires the addition of clean water only, and can be placed anytime without the need for batch plants or concrete trucks
  • Specially formulated to withstand underground conditions
Packaging

ACS Quick Drive is available in 1.2 tonne bulk bags.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…