menu

Enviro Agi Clean is a concentrated, environmentally friendly cleaner which is non-corrosive to the skin and most metal materials.

Uses

When diluted with water, Enviro Agi Clean can be used to effectively and efficiently clean cement dust and concrete residue from vehicles and machinery (concrete agitators, concrete pumps, level screeders) used within the pre-mix concrete industry.

Dilution Rate

For best results dilute the product with water at the rate of approximately 1 part Enviro Agi Clean to 2 or 3 parts water (1:2 or 1:3).

Note: Enviro Agi Clean can be used at 100% concentration in specific applications. Please contact to your ACS Area Manager for further advice.

Mixing and Application

Apply diluted Enviro Agi Clean to the affected surface using a broom. Rinse thoroughly with water prior to surface drying.

Impact on Base Materials

When diluted as per recommendations, Enviro Agi Clean is safe to use on most good quality paints and plastics.

The product will have very little affect on stainless steel, steel, bronze, copper and brass.

When applied to aluminium or zinc surfaces Enviro Agi Clean is more aggressive and may show some signs of affect after prolonged use.

Cleaning

Ensure all application tools are cleaned with water both before and after use.

Storage

If stored in its original container, and at temperatures between 5ºC and 30ºC, the product will keep for up to twelve months.

Health and Safety

During use, avoid inhalation of dust and contact with the skin and eyes. Wear suitable clothing, gloves, eye protection and respiratory protective equipment.

If contact with the skin occurs, thoroughly clean the area with plenty of fresh water and soap. In case of contact with the eyes rinse with plenty of fresh water and seek medical advice.

If swallowed, seek medical attention immediately – do not induce vomiting.

For further information consult the Safety Data Sheet (SDS) and read the product label carefully before use.

Features and Benefits
  • Removes cement residue and concrete quickly and effectively
  • Safe to use with very low odour and non-fuming characteristics
  • Replaces dangerous hydrochloric acid formulations
  • More effective than other acid replacement products
  • Much less corrosive to steel and aluminium than than hydrochloric acid
  • Cleans without leaving a residue
Packaging

Enviro Agi Clean is available in 20 and 200 litre drums, as well as 1000 litre palecons.

For further information consult the Safety Data Sheet (SDS) and read the Technical Data Sheet (TDS) carefully before use. SDS and TDS documents are available in the Resources section of this website and by contacting ACS Customer Service support line on 07 3412 8111 or 1800 077 744.

At ACS, our focus is on providing practical solutions and improving the application, life and performance properties of our products to not only meet specifications, but the ever increasing demands and safety requirements of the industries in which we operate. Using state of the art equipment, all products are a part of a continuous program of laboratory and field trials, research and standards testing. ACS also has a unique focus on high performance tailored formulations – developed at our Brisbane based R&D laboratory.

Product Focus

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Rapidseal VCD Grout

ACS Rapidseal VCD Grout has been specifically designed to enable the installation of a cost effective and permanent sealing system within underground coal mines – for the purpose of ventilation control and ground support.  The non toxic product is installed using a Langley grout placer pump or similar. By adjusting the water content of water…

CCS Industrial Epoxy XT100

CCS Industrial Epoxy XT100 is a two part, civil grade, 100% solids epoxy resin coating specially formulated for industrial and commercial concrete floors where a long lasting and durable surface is required. CCS Industrial Epoxy XT100 penetrates deep into concrete to seal, protect and provide a high level of resistance to chemicals, corrosive compounds and…

ACS Grout HES30

ACS Grout HES30 is a high performance, cement based grout that has been specifically designed to minimise bleed and segregation and is suitable for a wide variety of applications. Made from a blend of cements, graded aggregates and special additives which provide rapid strength development and excellent bonding characteristics, Grout HES30 is supplied as a ready to use…

ACS Construction Grout

ACS Construction Grout is a versatile, non-shrink cement based grout. It is supplied as a ready to use powder, which is made up of a blend of Portland cement, pozzolanic material, graded fillers and chemical additives. It can be used for general purpose grouting where it is necessary to eliminate shrinkage however it is specifically…